Reply to "🖼️ All the Pictures and Nothing of the Else"

magharees · October 21, 2020, 8:10am

Mesh screening, battle hardening and pot the sensor pcb

Hoping the low kv makes them a little conservative on the series rating.

I plan to pump max 60A into each motor given 7p of 30Q, iirc 30Q can do a burst of 20A but 15A continuous

PixelatedPolyurethan · October 21, 2020, 8:14am

done bro, but still, for the same price i could have gotten 600W more of unusable power, 5mm longer

and more boasting specs

magharees · October 21, 2020, 11:22am

I bet the stator is the same, the 63100 did not have room for a hall sensor pcb according to Bruno. You can add encoders instead?

Not sure how HFI is for ATB? I’ve tried it only on thane and I still get more stuffer than Spider

PixelatedPolyurethan · October 21, 2020, 12:11pm

I run HFI on the 63100 and it works perfectly!

Darkie02 · October 21, 2020, 1:00pm

Still think if you extend the axle an make a custom motor mount with bearing on the can side to make dule drive singe VESC it would then be a viable single drive board

Andrew · October 22, 2020, 1:00am

@Lee_Wright This is what I get for sending you free shit eh?

Andy87 · October 22, 2020, 4:58am

Don’t you see @Lee_Wright thirsty eyes looking at your pictures??? That’s all just love Andrew.

BillGordon · October 22, 2020, 5:57am

Your board vs. the board she told you not to worry about:

Wandagoner · October 22, 2020, 6:01am

if @Linny 's is OG Kush does that make yours Fancy Fentanyl?

BillGordon · October 22, 2020, 6:05am

My deck is sponsored by Viagra. FOR NO REASON WHATSOEVER.

Lee_Wright · October 22, 2020, 10:23pm

I put your picture in a love heart right?

glyphiks · October 22, 2020, 10:35pm

You should have used this one

Lee_Wright · October 22, 2020, 11:17pm

I did ask for submissions!

Abusfullofnuns · October 23, 2020, 3:23am

Cool. Like my first telephone. Crazy how excited I was to get a phone line to the room back in 1988.

Flasher · October 23, 2020, 3:30am

I’m currently working on making a backlit GMC logo for a friend’s truck. But that’s like 40 meters of filament…leaves 330m of it that I get for free

Wandagoner · October 24, 2020, 6:51pm

love the action shot!

Andy87 · October 24, 2020, 7:27pm

All credits go to my brave girlfriend who did jump into the middle of the dirt spray to take that picture (it’s actually just a screenshot out of a short clip)
Shamelessly pumping my insta story…

Flasher · October 24, 2020, 7:58pm

You pull/push forward on the handle?

Finger holes are the wrong way to pull behind you

SeanHacker · October 24, 2020, 9:51pm

Pulling. Been testing it and the finger holes are just fine for me and where I want them. Chamfered on both sides so it’s not like it’s uncomfortable or anything. It’s the same on either side. Or missing what you’re asking?

Venom121212 · October 24, 2020, 10:16pm

I always say this!

Shouldn’t the crescent shape of the knuckles be opposite to match your hand for when you’re pulling it?

Or maybe you push it like a lawnmower?